310-606-2222
Bel-Air Service Area
Bel-Air hillside home remodeled by Precise Building and Restoration
  1. Home
  2. Areas We Serve
  3. Bel-Air
Licensed General Building Contractor Serving Bel-Air

General Contractor in Bel-Air for Hillside Remodels, ADUs and Custom Homes

Kitchen and bathroom remodels, whole-house renovations, custom homes, roofing, retaining walls and fire-zone upgrades, permitted through LADBS under Bel-Air's hillside rules.

  • 5.0 rating on Google reviews
  • CSLB License #1113493
  • Free initial project estimate
  • Serving Bel-Air 90077
Overview

What Bel-Air Homeowners Usually Ask Us to Do

Precise Building and Restoration is a design-build general contractor with its office on Sepulveda Boulevard, just across the 405 from Bel-Air. Our crews reach Bel-Air Estates, Stone Canyon, Roscomare Valley and the streets above Sunset in minutes.

Most Bel-Air lots are hillside lots in a fire hazard zone, so the approval path matters as much as the design. We check your parcel's zoning, street width and overlays before drawings start, then give you a written scope, a fixed-price contract and a realistic schedule.

  • Remodel a kitchen and primary suite in a 1950s or 1960s hillside home and open it to the view.
  • Rebuild a whole house around new plumbing, wiring, HVAC and structural connections.
  • Harden a home against wildfire with a Class A roof, ember-resistant vents and noncombustible decks.
  • Repair or replace failing retaining walls, decks and drainage on a sloped lot.
  • Add a guest house, pool house or ADU where the lot and street allow it.
  • Build a new custom home on a hillside lot from grading through final finishes.
Services

Remodeling and Construction Services in Bel-Air

Remodeled kitchen with custom cabinetry and island

Kitchen Remodeling in Bel-Air

We remodel kitchens from layout through final trim: custom cabinetry, stone countertops, islands, panel-ready appliances, lighting and flooring, plus the plumbing, gas and electrical work behind them. In hillside homes we often remove walls to open the kitchen to the view, which means engineered beams and a structural permit.

Remodeled bathroom with walk-in shower and custom tile

Bathroom Remodeling in Bel-Air

We renovate primary suites, guest baths and pool baths: curbless walk-in showers, steam showers, freestanding tubs, heated floors, custom vanities, tile and waterproofing. In older homes we replace galvanized supply lines and cast-iron drains while the walls are open.

Whole-house remodel with open living area

Whole-House Remodeling in Bel-Air

For homes that need more than one room, we plan layout, structure, systems and finishes as one project: relocated walls, new glass openings to terraces, rewiring, repiping, new HVAC and coordinated interior finishes. We sequence the work around hillside access and the hauling limits on your street.

Two-story ADU built by Precise Building and Restoration

ADUs, Guest Houses and Pool Houses in Bel-Air

We build ADUs, junior ADUs, guest houses and pool houses where Bel-Air's fire and hillside rules allow them. Before design starts we check your street width, fire sprinkler and parking requirements, which decide whether an ADU is possible on your lot.

Custom home construction by Precise Building and Restoration

Custom Homes in Bel-Air

We build new homes on hillside lots, managing architecture, geology and soils reports, grading, caisson foundations, framing, systems and finishes. The design is drawn to the Baseline Hillside Ordinance size limits and Bel-Air's grading and hauling caps from the first set of plans.

Roof replacement on a Los Angeles-area home

Roofing and Wildfire Home Hardening in Bel-Air

We install and replace tile, metal and flat roofs as Class A assemblies, and add ember-resistant vents, enclosed eaves, noncombustible gutters and fire-rated decking. These upgrades meet the building standards for Very High Fire Hazard Severity Zones, which cover most of Bel-Air.

House foundation repair by Precise Building and Restoration

Foundations, Retaining Walls and Seismic Retrofits in Bel-Air

We repair settled foundations, build and replace retaining walls, install caissons and grade beams, and correct drainage on sloped lots. In older homes we add foundation bolting, cripple-wall bracing and shear walls during the remodel.

Modern backyard transformation with outdoor living area

Backyard and Outdoor Living in Bel-Air

We build terraces, pool decks, outdoor kitchens, covered loggias and hardscape on sloped lots, with fire-resistant materials near the house and drainage designed for hillside runoff.

Restored historic home by Precise Building and Restoration

Historic and Mid-Century Home Restoration in Bel-Air

We restore Bel-Air's Spanish, Traditional and mid-century modern homes while keeping original woodwork, glass walls and built-ins where possible. Behind the walls we add new plumbing, wiring, HVAC and seismic connections without changing the home's character.

Process

How a Bel-Air Project Moves From Plans to Final Inspection

  1. Consultation and parcel review

    We walk the property and pull its zoning record. We confirm the Hillside Area and fire zone status, the street width, the Hillside Construction Regulations and whether the Mulholland Scenic Parkway plan applies.

  2. Design, geology and engineering

    We prepare layouts and material selections, and your first three CAD designs are free. For hillside work we bring in the geologist, soils engineer and structural engineer early, because their reports shape the foundation and the grading quantities.

  3. LADBS plan check and permits

    We submit plans to LADBS, including grading and geology review where needed, answer corrections and pay fees on your behalf. Projects moving 1,000 cubic yards of soil or more also need a haul route approval.

  4. Pre-construction

    We schedule hauling inside the permitted window, arrange off-site truck staging, post the required permits and placards, and give your neighbors our schedule and a direct contact.

  5. Construction

    Crews work Monday to Friday, 8 a.m. to 6 p.m., with interior-only work on Saturdays. We keep narrow hillside streets clear, control dust and runoff, and protect slopes and trees around the work area.

  6. Inspections and closeout

    We schedule every LADBS inspection, including grading and deputy inspections, walk the finished work with you, complete the punch list and close out the permits so the records are clean.

Local requirements

What to Know Before You Build or Remodel in Bel-Air

Bel-Air layers some of Los Angeles' strictest hillside rules on top of the building code. They decide how big you can build, how much soil can leave the site, when trucks can run and whether an ADU is allowed.

Check this first

Bel-Air is part of the City of Los Angeles

Bel-Air is a neighborhood of the City of Los Angeles, not a separate city, so projects here are permitted by LADBS (the Los Angeles Department of Building and Safety). Its rules differ from neighboring Beverly Hills, which runs its own building department. We look up your parcel's zoning record before design, because it shows whether the lot is in a Hillside Area, a Very High Fire Hazard Severity Zone, the Hillside Construction Regulation district or the Mulholland Scenic Parkway plan.

Building just over the line? See our Beverly Hills service area page.

Permits through LADBS

Bel-Air projects go through LADBS plan check, and the nearest office is the West Los Angeles Development Services Center at 1828 Sawtelle Boulevard. Hillside remodels and new homes usually need a geology and soils report reviewed by the LADBS Grading Division before the building permit is issued.

Larger projects can also need clearances from City Planning, the Fire Department and LADWP. We track each one so a missing sign-off doesn't hold up the permit.

Bel-Air's Hillside Construction Regulations

In 2017 Bel-Air became the first neighborhood in Los Angeles with a Hillside Construction Regulation (HCR) district. It adds limits that apply on top of the citywide hillside rules.

HCR district limits · Bel Air–Beverly Crest
RuleLimit
Construction hoursMonday to Friday, 8 a.m. to 6 p.m.
SaturdaysInterior work only, 8 a.m. to 6 p.m.
Night lightingNo floodlighting of the site after 6 p.m.
Haul hoursWeekdays, 9 a.m. to 3 p.m.
Haul trucksUp to 4 per hour, 10 cubic yards or less each, staged off-site
Grading per site6,000 cu yd maximum (4,500 on substandard streets)
Haul route approvalRequired for 1,000+ cu yd of import or export
Very large homesSite Plan Review above 17,500 sq ft

Exterior work on a Saturday can be reported to LADBS and carries a misdemeanor penalty of up to $1,000, so we schedule exterior trades on weekdays only.

Size and grading limits under the Baseline Hillside Ordinance

Los Angeles' Baseline Hillside Ordinance caps a hillside home's floor area based on lot size, zone and how steep each part of the lot is. Steeper portions of the lot count for less buildable area. Height is measured along the slope, and grading is capped by a formula tied to lot size.

We run these numbers with your architect before design, so you know the maximum size before you pay for drawings.

ADU rules in Bel-Air

Most of Bel-Air is both a Hillside Area and a Very High Fire Hazard Severity Zone. City law bars most ADUs on lots in both zones unless the ADU has fire sprinklers, one off-street parking space, and the lot fronts a street with an unobstructed roadway at least 20 feet wide.

Many Bel-Air streets are narrower than 20 feet, so street width is often the deciding factor. California's housing department found the city's rule out of compliance with state law in November 2024, and City Planning released a draft amendment in 2026. We check the rules in effect when you apply, including options for a junior ADU inside the existing house.

Fire zone requirements

Most of Bel-Air sits in a Very High Fire Hazard Severity Zone. The 1961 Bel Air fire destroyed 484 homes, and Los Angeles responded by banning wood shingle roofs on new construction and adopting some of the strictest brush clearance rules in the country.

New homes, additions and re-roofs must meet California's wildfire building standards: Class A roofing, ember-resistant vents, ignition-resistant siding and decks, and tempered glazing. The Los Angeles Fire Department also inspects brush clearance on hillside properties every year.

Mulholland Scenic Parkway plan and private HOAs

Homes in upper Bel-Air near Mulholland Drive can fall inside the Mulholland Scenic Parkway Specific Plan. Depending on the scope, new homes and some additions there need approval from the plan's Design Review Board, which meets twice a month in Van Nuys.

Gated communities such as Bel Air Crest add their own HOA architectural review. That approval is separate from the city permit, and we submit to both.

Geology and seismic safety

State seismic hazard maps mark earthquake-induced landslide zones across much of the Santa Monica Mountains, including parts of Bel-Air. New homes and major additions in those zones need a geotechnical investigation, and hillside foundations often rest on caissons drilled into bedrock.

Los Angeles requires seismic retrofits for older soft-story apartment buildings and non-ductile concrete buildings, but not for single-family homes. A remodel is the easiest time to add one.

  • Foundation bolting and cripple-wall bracing for raised-floor homes.
  • Shear walls and hold-downs where large glass walls or open plans weaken the structure.
  • Steel moment frames for rooms built over garages and for walls of glass facing the view.
  • Retaining wall and drainage repairs to keep slopes and foundations stable.

What we find inside older Bel-Air homes

Much of Bel-Air was built from the 1920s through the 1960s, and many homes were rebuilt after the 1961 fire. Behind the walls we regularly find galvanized water lines, cast-iron drains, undersized electrical panels, single-pane glass walls and post-and-beam framing that needs added bracing.

We plan for these conditions in the estimate so they don't become change orders halfway through the job.

Water, sewer and power

LADWP supplies water and power in Bel-Air, and LA Sanitation handles the public sewer. Panel upgrades, new water meters and service changes for an addition or ADU go through LADWP, so we request them early.

Why Precise

Why Bel-Air Homeowners Hire Precise Building and Restoration

Hillside and fire-zone experience

We have completed more than 400 projects across the Los Angeles area, including hillside homes on the Westside. We plan for geology reports, grading limits, haul windows and fire-zone materials before construction starts.

Licensed, bonded and insured

We operate under California contractor license #1113493 with a $2 million aggregate general liability policy, workers' compensation coverage and a surety bond. Verify our license with the CSLB.

Fixed prices and one project manager

You get a detailed fixed-price contract and one project manager from consultation to closeout. Any change order is priced in writing before the work happens.

Design and construction under one contract

Our design-build model keeps drawings, engineering, permits and construction with one team. Your first three CAD designs are free, so you can compare layouts before committing.

Reviews on Google

What Our Clients Say

Read what clients wrote on our Google Business Profile, and ask us for references from hillside projects similar to yours.

★★★★★
Really happy with the work from Precise Building and Restoration. They did a great job remodeling our kitchen and bathroom. Everything came out clean and well-finished, and the crew was professional throughout the project.
Jose Fuentes · Kitchen and bathroom · Google, August 2026
★★★★★
Tony and his team did an outstanding job for my ADU and JrADU. He was able to work with my budget and everything was done on a timely manner. No games with Precise Building and Restoration.
Paytsar Chatalyan · ADU and junior ADU · Google, June 2026
★★★★★
From the beginning they were professional, responsive, and very transparent about the process and pricing. The crew showed up on time, kept the job site clean, and the quality of the work really shows in the final result.
Hugo Reyes · Construction · Google, March 2026
FAQ

Bel-Air Remodeling and Construction FAQ

Do you work in Bel-Air?
Yes. Precise Building and Restoration is a licensed general contractor serving homes throughout Bel-Air, including Bel-Air Estates, Stone Canyon, Roscomare Valley, Bel Air Crest and the hillside streets toward Mulholland Drive. Our office on Sepulveda Boulevard is just across the 405.
Who issues building permits in Bel-Air?
Bel-Air is part of the City of Los Angeles, so permits come from LADBS, the Los Angeles Department of Building and Safety. Hillside projects usually also need geology and soils review by the LADBS Grading Division, and some need City Planning or Mulholland design review.
Can I build an ADU in Bel-Air?
Sometimes. Most of Bel-Air is both a Hillside Area and a Very High Fire Hazard Severity Zone, where city law allows an ADU only with fire sprinklers, one off-street parking space and a street roadway at least 20 feet wide. These rules are under review, so we check the current requirements for your lot before design.
What hours can contractors work in Bel-Air?
Monday to Friday, 8 a.m. to 6 p.m. On Saturdays only interior work is allowed, from 8 a.m. to 6 p.m., and no construction is allowed on Sundays. Soil hauling is limited to weekdays from 9 a.m. to 3 p.m.
How much soil can I export from a Bel-Air lot?
The Hillside Construction Regulations cap grading at 6,000 cubic yards per site, or 4,500 on substandard streets, and the Baseline Hillside Ordinance can set a lower limit based on lot size. Importing or exporting 1,000 cubic yards or more also requires a haul route approval.
My home is in a fire zone. What does that change?
New roofing, vents, siding, decks and windows must meet California's wildfire building standards, including Class A roofing and ember-resistant vents. The Fire Department also inspects brush clearance every year, and ADUs face extra limits on fire-zone hillside lots.
Does my Bel-Air home need a seismic retrofit?
Los Angeles requires retrofits only for certain older apartment and concrete buildings, not single-family homes. Many older Bel-Air homes still benefit from foundation bolting, shear walls or steel frames at glass walls, and hillside lots in landslide zones need a geotechnical investigation before major work.
How much does a remodel cost in Bel-Air?
Cost depends on scope, existing conditions, materials, structural and geotechnical work, and site access. Narrow hillside streets, off-site truck staging and haul limits add time and cost compared with flat lots. We give you a fixed price once the scope is defined.
Where can I verify your license?
Our California contractor license number is #1113493. Check its current status on the California Contractors State License Board website.
Contact

Contact Our Team About Your Bel-Air Project

Send us your Bel-Air address, the work you have in mind, your timing and a rough budget. Photos, surveys or existing drawings help. We will reply with the approvals your project needs and a time to walk the property.

Map of Bel-Air

Precise Building and Restoration on Google Maps

Scroll to Top